NO TEXT MESSAGESPHONE CALLS ONLYNEW Blueprint Engines 400 Small Block Chevy Bare block. Features 9.025 Deck Height, 4 bolt spayed Main caps, 2 Piece Rear Main Seal, Main Priority oil system. Unfinished bores. Will need to be bored to your finish specs. Has a small neck to one cylinder top edge as can be seen in picture. $1400.00 Again Call only, NO text messaging, too many scammers.
Similar
BOSE QUIET COMFORT 15 HEADPHONES. If you love music they sound incredible. They also have noise cancelling and fold flat which is great for travel. Engine roar fades to a whisper. Comes with new ear cups, new inline talk cable and Bose protective case. Great for anyone who loves superior sound and memory foam comfort. Within every pair of QC15 headphones, advanced electronics use microphones in...
I have a 1969 Pontic 350 complete except carb ran when pulled needs rebuilt 9790079 $500 ,Pontiac 1976 400 block crank rods pistons oil pan 500557 $350 ,6x heads $250,1965 389421 67cc closed chamber heads complete orange in pics ,also have a Pontiac 350 turbo$150 and a Pontiac 400 turbo $250 transmissions ,aluminum lt1 heads off 1996 corvette $300 calls only will not answer emails
This is a service for head bolt thread repair on GM LS engines and other GM engines that have the M11x2.0 thread. If you are reading this, you have a thread that has pulled out while putting a cylinder head back on. The tool you need to do this is very expensive, and we have it. Time-Sert 3700. We had this exact problem and had to purchase the tool to do it, but before we did we called everyone...
CHOATE ENGINEERING PERFORMANCE IS LOCATED IN WHITEVILLE, T.NLong blocks, short blocks, diy kits, or full runners for all powerstroke, cummins and duramax.. just give us a call so we can give you an exact estimate and answer any questions you may have concerning an engine build.visit us at Choates engineering and performance on facebook.
Rebuilt 350 SBC bored to 360 cid. 4 bolt main block with Scat 9000 lite crankshaft, Eagle H-beam Rods, Wiseco forged flat top 2 valve relief pistons, New set of Clevite H bearing and Total Seal file to fit piston rings. Rotating assembly has been balanced. New Comp Cams camshaft, lifters, pushrods and rocker arms. Rebuild GM aluminum angle plug cylinder heads with port work. New valves, valve s...
Wow, you cant believe the updates on this home Granite countertops, stainless steel appliances, updated fixtures, butcher block top on kitchen island and not a stitch of carpet in the entire house From its beautiful engineered laminate floors, to the heated and cooled Arkansas room, to the covered deck off the master, this house has to be seen to be believed. Finish it off with a fenced yard an...
$20,000

1990 SeaRay 310

Twin 7.4 big block Chevrolet engines on board heat and air diesel generator 30 onboard battery charger three brand new Heater for both engines sonar radar system CB television antenna lots of room RV on the water
This engine came from a 1982 F150 pickup. The truck sat since 2012. To get it running I replaced the plugs fuel pump. It starts right up and runs very well. No smoke, no knocks and no funny noises. It showed normal oil pressure on the Ford dash gauge. I have no idea how many miles are on the engine or anything about the internal condition. I did notice some oil at the front of the intake block ...
I have a C6 transmission for small block Ford engines This is the hard to find unit that fits 289,302, 351W, 351C and 300 6cylinder engines. The distance between the top two transmission to block mounting holes is 5 18 inch. It came out of a 1982 F100 with a 302 engine. Fluid looked ok and there was no metal in pan. The case is aluminum and has no damage or cracks. The torque converter is inclu...
The engine block is cracked so its just for scrap parts. The engine wants to turn over but it just isnt worth for me to fix it up. You will need to bring a trailer to pick it up
1 + ... Next >