This ad is for a stock Porsche Type IV 66mm crankshaft assembly without connecting rods for a 1970 - 1976 Porsche 914-4 with a 1.7 liter engine and or a 1.8 liter. The crankshaft will fit a VW as well so please do your homework to insure it is correct for your needs. I need to send the crankshaft to my crankshaft machine shop to have it cleaned, measured and repaired if necessary. As well as ma...
This ad is for a used OEM crankshaft pulley for what I believe to be for a 1979 1989 Porsche 911S or Carrera. Please do your homework to insure it is correct for your needs. The pulley It measures 5 1/4" x 1 1/2" and appears to be in very good condition The Porsche part number I think is 911.102.133.00 I am asking $200.00 for the pulley plus $18.50 in postage and paypal fees.
This ad is for a used OEM 71mm stock crankshaft for a 1973 - 1976 Porsche 914-4 2.0 liter. The crankshaft could be used in other applications too so please do your homework to insure it is correct for your needs. The crankshaft was sent to Custom Crankshaft Repair where it was thoroughly cleaned and magnafluxed and nitrided followed by micro-polishing, face flywheel flange & square and smooth. ...
This ad is for a used OEM crankshaft and connecting rods for a 1969 911 T and or a 1970 - 1972 Porsche 914-6. The crankshaft may fit other Porsche year models as well so please do your homework to insure this is correct for your needs. The crankshaft was sent to Custom Crankshaft Repair recently and was professionally measured and checked for wear and was found to be std / std. The crankshaft o...
Similar
Rebuilt 350 SBC bored to 360 cid. 4 bolt main block with Scat 9000 lite crankshaft, Eagle H-beam Rods, Wiseco forged flat top 2 valve relief pistons, New set of Clevite H bearing and Total Seal file to fit piston rings. Rotating assembly has been balanced. New Comp Cams camshaft, lifters, pushrods and rocker arms. Rebuild GM aluminum angle plug cylinder heads with port work. New valves, valve s...
This ad is for a used 2R magnesium crankcase without studs for a 1970 Porsche 911 T 2.2 liter and perhaps other Porsche year models too. Please do you homework to insure this is correct for your needs. It is my understanding that the very early 2.2 liter 2R mag cases are outstanding in terms of quality. I suppose it makes sense because first builds are always more closely monitored during the m...
This ad is for a used OEM timing gear, intermediate ring and drive wheel for the crankshaft of a 1984 - 1989 Porsche 911 Carrera with a 3.2 liter engine although I think the parts will be interchangeable with other year model Porsche cars as well based upon the early part numbers. The gears and drive whee are in very good condition and show no signs of wear what so ever and can be used as is wi...
This ad is for a set of six used OEM connecting rods for a 1972 - 1977 Porsche 911 2.4 liter and or a 2.7 liter crankshaft. I believe these connecting rods are also correct the early 3.0 liter engines but please do your homework to ensure that these are correct for your application. I will help answer questions if I can or make additional photographs if necessary. The foundry part number is 901...
This ad is for a used OEM flywheel without starter ring for a 1978 - 1983 Porsche 911 SC with a 915 transmission. Please do your homework on this item because I am not at all sure of things. The flywheel is in good condition and is within the wear limits identified by Porsche technical specifications booklet. Included are the 9 flywheel to crankshaft bolts and the pilot shaft bearing. The Porsc...