More Filters
This ad is for a used hydraulic camshaft for carburetors by Web Cam including a bolt on drive gear. The camshaft will fit a 1970 - 1976 Porsche 914-4 as well as any VW Type IV engine. I don't know the lift or duration of camshaft but the fellow I bought it from said it was screamer. He raced a 914-4 with this camshaft and placed in the top 5 nationally in FP. I notice there is a wear mark on th...
Similar
This ad is for a new pair of aluminum alloy carburetor intake manifold kit with gaskets and fasteners for a 1970 - 1976 Porsche 914-4 or a VW Bus with a VW TIV. These are universal manifolds and will fit the TIV engine or the Porsche TIV engine This manifold design allows more torque at the low end and allows for better clearance in the engine compartment. An ideal solution for a Type II bus. T...
This ad is for a new engine wiring harness for a 1975 to 1977 Porsche 911 2.7 liter with carburetors although I think it would fit a standard EFI but not the CIS. This wiring harness is setup for a remote voltage regulator and a 3 pin CDI. It is a new harness built from the ground up with everything new with the exception of the restored connectors. I bought it several years ago for a 2.8 liter...
This ad is for one OEM 2.2 liter cylinder head for a 1968 -1970 Porsche 911T and or a 911E with carburetors. As you can see the cylinder head is a bare casting with no valves or valve train components. Valve seats are installed. Aside from a broken cooling fin at the corner of the top side of the cylinder head is in excellent condition. Aside from the broken fin I don't see anything wrong. Inst...
This ad is for a used Bosch warm up regulator for a what is thought to be a 1974 - 1977 Porsche 911 with CIS. I am not at all positive what other year models this WUR might fit so please do your home work. The Bosch part number on the body of the WUR is 0 438 140 033. Additionally there is a 472 and a 086 number on the body. This part was removed from a 1976 911 S as I recall when the guy I got...
This ad is for a used ignition distributor assembly for a 1970 - 1976 Porsche 914-4 with carburetors. This distributor I think has a centrifugal advance and it should fit high performance VWs with many different engine configurations. Please do your homework to insure that the distributor is appropriate for your application. The number on the distributor is 0-231-178-009. It is not stamped Bosc...
This ad is for an incomplete set of use used rocker shaft fasteners for a 1965 - 1989 Porsche 911 / 914-6 / 930. I am not at all positive on this so please do your homework. The fasteners look to be new but were not stored properly and have a bit of surface rust. I am soaking in carburetor cleaner and will retake photographs later and update the ad. I checked with Stoddard today and the MSRP fo...
This ad is for a used 2R magnesium crankcase without studs for a 1970 Porsche 911 T 2.2 liter and perhaps other Porsche year models too. Please do you homework to insure this is correct for your needs. It is my understanding that the very early 2.2 liter 2R mag cases are outstanding in terms of quality. I suppose it makes sense because first builds are always more closely monitored during the m...
This ad is for used high performance ignition setup for a 1970 - 1976 Porsche 914-4 and or a 1965 - 1969 Porsche 912. The hi-performance ignition should also fit any VW sedan, Ghia, bus and or a square back. Crane shows 4 cyliner, 6 cylinder and 8 cylinder...just do your home work to insure it is correct for your needs. The ignition setup has been tested by Crane and is in very good condition. ...
Rebuilt RARE early1964 HiPo engine. C4OE-6015-C Block date 3M2 bore .040 serial number 3469 stamped on driver's side of block. 5 bolt block. Matching date HiPo heads 3L21 Original HiPo crank turned .020 HiPo C3 rods Flat top pistons C3OF-AJ HiPo carburetor Dual Point C3OF-12127 HiPo Distributor dated 3M2 Original Shelby Buddy-Bar valve covers HiPo flywheel balanced to the rotating assembly Corr...
Your Listing Here